Highside Chemicals
Supco
   
 
 
     

Highside Leak Lock

Highside Leak Lock Gold
LEAK LOCK
How to Use Video
Highside Chemical
11114 Reichhold Road - Gulfport, Mississippi 39503, USA

800-359-5599
228-896-9220
Fax: 228-896-9544

Email

 

Leak Lock high strength pipe joint sealant

Leak Lock is a state-of-the-art high strength, pipe joint sealant consisting of chemically resistant film formers, plasticers, reinforcing fillers and solvents .

  • A resin based brushable paste which remains permanently flexible, adheres to internal surfaces and fills voids
  • Ideal for metal and plastic materials subject to extreme vibrations
  • Effective in temperatures from -200ƒF (-93ƒC) to 400ƒF (204ƒC), full vacuums and pressures to 10,000 PSI

Leak Lock can be used on all metal or plastic materials, including but not limited to, aluminum, aluminum alloys, cast irons, copper, copper alloys, (brass, bronze, etc...), magnesium and magnesium alloys, carbon steels, stainless steels, galvanized surfaces, PVC, CPVC, ABS, fiberglass, black polypropylene, and kynar. Leak Lock should be applied to threaded joints, flanged joints, gasket surfaces and all mating surfaces where a fluid-tight seal is required.

Leak Lock seals a broad range of chemicals including all refrigerants such as R-12, R-22, R-502, R-134A, etc., all CFC, HFC and HCFC refrigerants, petroleum products, natural and manufactured gases, steam, water, air, etc. No other sealant offers the application range of Leak Lock. Use alcohol as a cleansing solvent prior to setting.

Available in 1 1/3 oz. tube; 4 oz. & 16 oz. brush top plastic jars; 1 gal. can

Product Specifications

What is Leak Lock?

Leak Lock is a state-of-the-art high strength, pipe joint sealant consisting of chemically resistant film formers, plasticers, reinforcing fillers and solvents .

How It Works
When Leak Lock is applied to pipe joints, it adheres to the mating surfaces. After joints are assembled, Leak Lock sets to form a chemically resistant flexible fluid-tight seal.

How to Use It
Leak Lock should be applied to clean joint surfaces, either with the applicator brush or any convenient spatula. Apply Leak Lock to both mating surfaces. Tack should be allowed to develop before joints are assembled.

Where to Use It
Leak Lock can be used on all metal or plastic materials, including but not limited to, aluminum, aluminum alloys, cast irons, copper, copper alloys, (brass, bronze, etc ...), magnesium and magnesium alloys, carbon steels, stainless steels, galvanized surfaces, PVC, CPVC, ABS, fiberglass, black polypropylene, and kynar. Leak Lock should be applied to threaded joints, flanged joints, gasket surfaces and all mating surfaces where a fluid-tight seal is required. Special Applications - Leak Lock is ideal for joining dissimilar metals and materials. Prevents loosening of nuts, bolts, plugs and fittings. Call Highside for specific applications and compatibility.

Typical Physical Properties

  • Viscosity ...... 25,000-100,000 cps
  • Consistency ...... flowable Paste
  • Color ...... light Blue
  • Solvent ...... ethanol and isopropanol
  • Pressure ...... full vacuum to 10,000 psi
  • Temperature ...... -200°F to +400°F
  • Toxicity ...... non-toxic
  • Shelf Life ...... Indefinite when kept Sealed
  • Material Safety Data Sheet is available from Highside or can be downloaded from our web site:
  • http://www.highsidechem.com

Leak Lock Gold
Contains Teflon®

Leak Lock - Successes,
The following is a partial list of the materials and fluids that Leak Lock has successfully sealed:

Refrigerants:

All CFC'S, HFC'S AND HCFC'S Including but not limited to ...

  • R-717 (ammonia)
  • R-744 (carbon dioxide)
  • R-11 (trichlorofluromethane)
  • R-12 (dichlorodifluromethane)
  • R-21 (dichlorofluromethane)
  • R-22 (chlorodifluromethane)
  • R-113 (1, 2-trichlorotrifluroethane)
  • R-114 (1,2-dichlorotetrafluroethane)
  • R-40 (methyl chloride)
  • R-30 (methylene chloride)
  • R-290 (propane)
  • R-764 (sulfur dioxide)
  • R-134a (1,1,2-tetrafluroethane)
  • R-13, R-13BL, R-500, R-502, R-503, R-123, R-124, R-401A, R-401B, R-402A, R-402B, R-403B, R-406A, R-408A, R-409A, R-23, R-236FA, R-404A, R407A,R-407B, R-407C, R-410A, R-507, R-508.

Fuel Gasses:

  • Natural Gas
  • LPG "Liquefied Petroleum Gas"
  • LNG "Liquefied Natural Gas"
  • Propane
  • n-Butane
  • Isobutane

Fuels:

  • Gasoline (petrol; motor fuel)
  • Aviation Fuels (avgas; jet fuel)
  • Fuel Oils
  • Diesel Fuel Oils
  • Gas Turbine Oils
  • Hydrazine*
  • Kerosene
  • Gas Oil

Refrigeration Oils:

  • Mineral Oils, Napthenic
  • Mineral Oils, Paraffinic
  • Polyol Esters
  • Polyalphaolefins
  • Alkylbenzenes

Solvents:

  • Water (soft;hard;potable)
  • Seawater (saltwater)
  • Deionized Water
  • Pentane
  • Hexane
  • Cyclohexane
  • Heptane
  • Petroleum Napthas
  • Mineral Spirits
  • Acetone
  • Toluene
  • Xylene
  • Perchloroethylene
  • D-Limonene
  • Turpentine
  • Pine Oil
  • Lacquer Diluent
  • Rubber Solvent
  • VM&P Naptha
  • Stoddard Solvent
  • 140šF Solvent
  • Deodorized Kerosene
  • Medium-Flash Aromatic Naptha
  • High-Flash Aromatic Naptha
  • Dipentene
  • Methylene Chloride
  • 1,1,1-Trichloroethane
  • 2-Nitropropane
  • Orthodichlorobenzene
  • Monochlorobenzene
  • Chloroform
  • Ethylene Dichloride
  • Trichlorethylene
  • Propylene Dichloride
  • Aliphatic Solvents
  • Acids, Dilute
  • Caustics, Dilute
  • Aromatic Solvents
  • Glycerine
  • Chlorinated solvents

Industrial Gases:

  • Acetylene
  • Chlorine, anhydrous
  • Air
  • Carbon Monoxide
  • Ammonia, anhydrous
  • Argon
  • n-Butane
  • Carbon Dioxide
  • Ethane
  • Ethylene Chloride
  • Fluorine
  • Hydrogen
  • Methane
  • Neon
  • Nitrogen
  • Nitrous Oxide
  • Oxygen (Industrial Only)
  • Propane
  • Propylene
  • Silane
  • Xenon
  • Tetrafluoromethane
  • Helium

Oils:

  • Mineral Oils
  • Soybean Oil
  • Coconut Oil
  • Tall Oil
  • Peanut Oil
  • Rapeseed Oil
  • Menhaden Oil
  • Vegetable Oil
  • Animal Oil

Leak Lock is not recommended for use with alcohols.

CURE TIME: Leak lock will cure and be ready for service in as little as 20 minutes or no more than 24 hours depending on pipe size and temperature of application.

Actual set times are dependent on pipe size and ambient temperature, but generally are as follows: 0 to 1/2" = 1 to 2 hours; 1/2" to 1 1/2" = 4 to 6 hours; 2" to 4" = overnight. Use alcohol as a cleaning cleansing solvent prior to setting and for clean-up.

 


HOME
SDS - MSDS LINKS
HOW TO USE PRODUCT VIDEOS
 
 
CONTACT US